uv涂料瞬时固化灯、紫外线节能固化灯、uvled面光源、uv

本产品适合于现代工业各类固化，是一款尖端，节能的固化光源。在许多工业领域都有很广泛的应用。

1、uv胶、uv漆的固化。

2.uv涂料的瞬时固化。

3.木业涂装，能使涂层干燥的更快、更均匀，光泽更好。

UVLED surface light source, is a semiconductor directly generated by the light emitting device is a high power LED chip according to a certain proportion of the integrated emission wavelength of 200nm to the formation of 450nm peak wavelength of light of a wavelength of 200nm to 450nm band.

UVLED面光源具有出光柔和、不伤眼、省电、光线自然、照射面积广、光斑均匀、寿命更长，光照更强等特点，LED式紫外线平衡光源用于LCD PCB，等曝光。比传统的汞灯更节能、更环保！

UVLED surface light source with light soft, not to hurt the eyes, electricity, light, wide area and natural irradiation facula, longer service life, better light characteristics of LED type ultraviolet balance source for the LCD PCB, exposure. More energy, more environmentally friendly than conventional mercury lamp!

UV LED面光源特性

UV LED surface light source characteristics

1.传统LAMP方式，大功率光源散热面小，即使用大量散热器也无法快速导出热量，因此光衰变快。led面光源同样功率散热面比UV LED点光源大几十倍，散热效果很好。寿命可达到25000-30000个小时。使用寿命不受开闭次数影响，采用电缆输出，相对比传统LAMP方式照射机，更换灯频繁，耗电功率高，还需紫外光纤输出，LED-UV采用电缆输出可以为您减少设备耗材成本，提供设备利用率。

1 traditional LAMP mode, cooling high power light source surface is small, which use a lot of radiator was not as quick to heat, so the light decay soon. LED surface light source, the same power radiating surface tens of times larger than the UV LED point light source, good heat dissipation effect. Life span can reach 25000-30000 hours. The service life is not affected by the switching frequency of the cable output, compared with traditional LAMP irradiation, the frequent replacement of lamp, power consumption is high, still need UV optical fiber output, LED-UV output by cable, you can reduce the equipment cost of consumables, equipment utilization rate.

2.发光部件LED波峰为365nm,光谱分布为360nm到370nm,无红外光发出，所以被照射产品的表面没有温度的提升，而传统LAMP式紫外线照射机一般都会使被照射产品表面升高60-90度，使产品的定位发生位移，造成产品不良。

2 light emitting component LED crest is 365nm, the spectral distribution of 360nm to 370nm, no infrared light emitted, so the surface irradiation products without the temperature increase, while the traditional LAMP type ultraviolet irradiation machine will generally make irradiated products surface rise 60-90 degrees, the product positioning of displacement, resulting in poor product.

3.众多LED发光点均匀分布，多组为紫外光照射优化设计的专业镜头组，照射性均匀，边缘和中心的照射强度变化不超过3%，一致性**，这是汞灯无法比拟的。

3 many LED light-emitting points evenly distributed, multiple sets of UV irradiation to optimize professional lens design, irradiation of the uniform change of radiation intensity edge and center of not more than 3%, consistency is excellent, this is mercury incomparable.

4.光输出稳定，光照更强、能量更高、均匀性更好，瞬间点亮，即刻达到100%功率紫外输出，照射强度可达1200mW/cm2 ，有效发光效率是汞灯的10倍以上，提高了工作效率 。

4 stable light output, light is stronger, higher power and better uniformity, momentary, immediate reach 100% power UV output, irradiation intensity can reach 1200mW/cm2, the effective luminous efficiency is more than 10 times the mercury lamp, improve work efficiency.

5.可根据用户的需要定制发光区域的形状、大小

5 according to the shape and size of the needs of users to customize the emitting region

6. LED-UV光源使用时无需灯管预热，不含有毒物质汞。相比传统LAMP方式照射机功率消耗几百瓦，甚至上千瓦，使用时需预热约10多分钟，灯管还含有毒物质汞。LED-UV面光源是替代传统光源技术的一种更安全、更环保的选择更符合节能环保的要求。

6 LED-UV light source without the use of the lamp preheating, does not contain toxic mercury. Compared with the traditional LAMP irradiation machine power consumption of hundreds of watts, even when using kilowatt, preheating of about 10 minutes, also contain toxic mercury lamp. LED-UV surface light source is an alternative to traditional light source technology more secure, more environmentally friendly option is more in line with the requirements of energy-saving and environmental protection.

7. LED-UV控制器的体积约为传统LAMP方式照射机体积的1/8，使设备的安装更加简单，减少生产现场的场地占用面积。照射头充分考虑精密生产的空间要求，使设备的安装更方便，另外小照头采用风扇散热设计，充分保障LED长时间照射的能量稳定及使用寿命。

The 7 LED-UV controller volume is about traditional LAMP irradiation machine volume 1/8, which make the installation more simple, reduce the occupied area of the site of production. Irradiation head considering precision production space requirements fully, which make the installation more convenient, another small head with fan cooling design, fully guarantee the energy stability and service life of LED long time irradiation.

UV LED面光源用途

UV LED surface light source uses

大面积固化、

A large area of curing,

电线、光纤外涂层光固化涂料

Wire, fiber coatings curing coatings

喷墨打印

Ink jet printing

材料照射催化

Catalytic materials irradiation

生物实验

Biological experiment

处理发霉的食品（发霉的玉米、大豆及其加工制品含有大量的致癌物质）

Processing moldy food (corn, soybean and its processed products moldy containing large amounts of carcinogenic substances)

了解更多