FA FB503和FA FB5037细纱机

FA/FB507细纱机设备图文介绍

设备图片介绍：图片1；↓

设备文本介绍: ↓

 

 

 

优质是其根本

●主传动通过王轴，传动直径0250毫米的滚盘带动锭子运转。中墙板采用框式结构，【型龙筋，角尺型短机粱，紧凑稳固机架重心低，可适应各种升降动程。

●能生产预定纱线长度的优质管纱，升降杠杆采用蜗轮箱传动单叶成形凸轮，凸轮的形状使管纱成形

能适应自动络筒机的高速退绕。

●牵伸结构卷与绕结构是经过大量科学实验的**优化设计。雏生产**好的纱线，**少断头率。在适纺

纤维种类和纤维长度方面通用l生强，范围大。

●各种国产棉型摇架厦SKF摇架、l NA与RIETER气加压摇架均可配套的牵伸系统．并可选配清洁前罗拉

的磁性绒辊，选用锭盘直径m 22mm或tl- 20 5mm的

 

ITS  PRINCIPAL-HIGH  QUALITY

●For main driving the tension pulley with diameter of 250mm which is driven by the main shaft is to drive the spindles to run. The spring piece adopts a frame-type design, 【-shape  short splndle rail and angle square-type short roller stand. which is compact and stable,with a low center of gravity suitable for all kinds of lifting motions.

●Able to produce excellent cops for presetting length. As for lifting lever. worm wheel box is used to drive the single builder cam, whose shape makes the cop formation suitable for the high-speed unwinding of automatic conewinder.

●The drafting and winding construction is the optimal design through lots of scientific

experiments it can produce the best yarn with the lowest breakage. it is versatile and widelyused with respect to spinnable fibre type and fibre length

●       Its drafting system can be equipped with all kinds of stateproduce cotton type pendulum arms. SKF. INA and RIETRER pendulum arms Magnetic clearing roll can also be ｓｅｌｅｃｔed to clean the front roller it is optional to use the low-noise power-saved spindle with the spindle wharve diameter of 22mm or205mm

 

高效是其目标

 

●机身窄，左右锭子中心距680毫米，空间利用率大。

●FA/FB507型细纱机除了有可的工艺性来保证纱线质量外，其制造陛同样是精良的。传动齿

轮均采用优质钢。高速级传动采用同步齿形带，安装方便，噪音低。牵伸传动齿轮采用斜齿，平

稳可靠。

●采用高强度平皮带传动主轴，配用变频器调节锭速。可选用6/4极双速高效节能电机。

●根据粗纱卷装大小，可选配单层四排（适应粗纱**大直径0 1 3 5毫米）或单层六排（适应粗纱**

大直径d.152毫米）的纱架。

●风箱密封性能好。

 

ITS  OBJECTIVE-HIGH  EFFICIENCY

 

●Narrow machine width. the distance between the centers of the two opposite spindles on

either side of the machine is 680mm, which utilize the space effectively.

●Besides the reliable technology to ensure the yarn quality, the ring spinning frame is

exquisitely manufactured. High-quality steel is adopted for all driving gears of overall

machine For high speed driving.Helical timing belt is used lo ensure convenient erection and

low noise Helical gears are chosen for drafting and driving gears, which make them stable and

reliable

●Use high-tension flat belt to drive the main shaft. equip it With inverters to adjust spindle

spaed. choose to equip it with 6;4 poles doublespeed high-efficiency motor which

saves power

●According to the roving package size.choose to equip single-layer 4-row creel（suitable for

roving with max dia of 135mm） or single-layer 6-row creel （suitable for roving whith max. dia

Of 152mm）

●Suction box sealed well by silica gel

 

自动化程度

●**早采用国际先进水平的程序控制器及变频速器。

●运转中能数字显示前罗拉线速度、锭速、捻度、定长和班产。

●纺纱过程中任何时候关机，能自动适位停机。

●需要时，可使钢领板提前自动下降及自动适位停机。

●纺纱至规定纱线长度时，可使钢领板自动下降及自动适位停机。

●开机前能使钢领板自动复位：

●在纺纱过程中，可自动变速，亦可手动变速。

●配用电动落纱机，落纱前能自接通落纱机电源．，

    

 

HIGH  AUTOMATION

●First adopt the internationally advanced programme controller and the speed-adjusting inverter

●While the machine is running. digital  display can show the linear speed of front roller, spindle speed, twist range.presetting length and shift output

●The frame can stop at a praper position automatically, whenever lt is required  during the spinning process

●If needed. the r Jng rail can wing down  automatically in advance and the machine can stop automatically at a proper position

●When  spinning  the  yarn  to the  presetting length. the ring rail will wing  down and stop automatically at a proper pasition

●Before starting the machine, the ring  rails W…reset themselves at the sta rting position automatically

●During spinning process, the spindle speed can be changed automatically or manually

●Equipped with auto-doffer, the power supply will be put through automatically before doffing

 

 

操作与管理可

●车头传动及牵伸传动，有滴浊润滑装置进行定时定量滴油，保证机器正常远转。

●传动齿轮采用统一模数、孔径和宽度，各种变换齿轮互相间可通用，减少了备用齿轮的品种和数量。

●有适用于棉型笛管和适用于中长纤维支管的断头吸入装置。

●各种控制与操作开关，集中于车头面板上。

●车头与车尾比机身窄使用电动蓓纱机时毋需预拔纱管

Operation and management

● To ensure tha normal running ofthe frame, the driving and fixed time by the lubrication system

●Change gears for drafting,twisting,and winding are of the same modula.bore diameter and width. and therefore

spare gears.

●Equipped with the broken yarn and suction device,which can borh fit to cottoh-type flute and fibre Sub-pipe

●All the conrtolling and operating buttons are concentrated on the pannei of the headstock.

●Since both the headstock and the endstock are more narrow Than the middle portion,it is unnecessary to pull out the bobbins

in advance befora auto-doffing

 

技术参数/Main   spcifications

锭距/Spindle gauge（mm）	70
锭数/ Spindle number:	504.492.480.456.444.420.408.396.384.372.360.96锭数etc
纲领直径/Dia.of diameter（mm）	38,42,45
筒管长度/Tube   length（mm）	205，230
适纺线密度/Spun yam count （tex）	6-96（100-6Ne）常规范围Normal  13-36（45-16）Ne
牵伸倍数/Drafing times:	10-50
捻度/Twist range	260-1500捻t/m
锭速/ Spindle speed range（r/min）	12500-18500;常规范围Normal  12500-16300
捻向/Twist	Z,Z或or   S
粗纱卷装/Roving package	￠135*320，￠152*460（Max）
适纺纤维/Spinnable fiber	棉、棉型化纤及65毫米一下中长化纤的纯纺或混纺

 

机器底脚图/Floor space of the machine

锭数 Spindle number	n	L1	L2	L3	L A=900    A=1300
504	12	15120		1260	19540	19940
492	12	15120		840	19120	19520
480	11	13860	840	840	18700	19100
456	11	13860		840	17860	18260
444	10	12600	840	840	17440	17840
420	10	12600		840	16600	17000
408	9	11340	840	840	16180	16580
396	9	11340		1260	15760	16160
384	9	11340		840	15430	15740
372	8	10080	840	840	14920	15320
360	8	10080		1260	14500	14900
	1	1260		840	5260	5660

 

底板厚度 Thickness of base plate	B	h	h1
正常 General condition	TEJ	45	65
增加50mm Specific condition	TEJ282-09	95	115

 

设 备 配 置 及 报 价 介 绍

FA503细纱机基本配件名称       产  地

锭子   上海

罗拉   常州

摇架   常德

皮辊轴承     上海

备注：本厂细纱机一律以上海纺机为标准，按山西经纬标准为依据，设备配置精良，产品质量可靠，售后服务完善。

 

张家港金桥轻工机械有限公司    地址：张家港市塘桥镇富民路180号    邮编:215611

联系人：代立州（先生  销售工程师）      手机:15851623464         传真：0512-58447226

 

了解更多